The official learned that the NF-1 memory cooler mounted on the motherboard fixed holes and built-in two 5020 fans, the official recommendation in the ATX motherboard with the CPU water-cooling cooler use.

The cooler has overall dimensions of 120/62/28.1mm, with a square shape, five sides are hollowed out and covered with rectangular mesh holes, making it compatible with memory up to 54mm.

The cooler has a 4Pin PWM / 3Pin ARGB interface, with a speed of 600-3600 RPM ±10% and an airflow of 1.3-9.11 CFM; the ARGB light effects can be synchronized, and it is compatible with the ARGB tuning software of major motherboard manufacturers.

The post Jonsbo NF-1 memory cooler listed now, dual 5cm fans, starting at RMB 69 appeared first on TechGoing.

According to Jonsbo, as the overclocking potential of many DDR5 memories has been realized, the accompanying high temperature problem has also plagued gamers. Jonsbo has launched the NF-1 memory active cooling vest, which dramatically improves the cooling efficiency of memory to help higher frequency and more stable operation.

As you can see in the picture above, this memory cooler is mounted on the motherboard’s mounting holes and has two built-in 5020 fans. It is officially recommended for use with CPU water coolers under ATX motherboards.

Josper’s new NF-1 memory cooler parameters are as follows:

The post Jonsbo Announces NF-1 Memory Cooler: Built-in Dual 5cm Fans appeared first on TechGoing.

According to the official introduction, the N3 shell is made of one-piece aluminium-magnesium alloy, and the surface is finely sandblasted, with a full metal texture; it adopts the upper and lower compartment structure design, and the motherboard compartment supports ITX motherboards and full-height expansion cards and supports MINI tower radiators;The ventilation holes on the front panel cooperate with the rear window fan to provide a good heat dissipation solution; the hard disk compartment supports 8-bay hard disk installation, and the front Type-C interface provides high-speed data transmission.

The post Jonsbo released N3 NAS chassis: 8-bay design, supporting ITX motherboards appeared first on TechGoing.

According to reports, the motherboard supports MATX motherboard, equipped with 2.5 surfaces curved glass, suitable for desktop multi-angle arbitrary placement of display surface.

The body is made of an aluminum alloy shell + double curved glass material, the internal vertical air duct design, the top panel supports 120mm * 2 (support 240 water cooling), and the bottom supports 120mm * 2 (fan position).

In terms of compatibility, this case supports air cooling radiators ≤ 165mm in height, water cooling supports 240mm all-in-one water cooling radiators, graphics cards are limited to 280mm in length, power supplies support ATX models, and the interior supports the installation of two 3.5-inch mechanical hard drives.

JOSEPH TK-1 chassis is now on the shelves, priced at RMB 599.

The post JONSBO TK-1 Chassis: 2.5-Sided Curved Glass, MATX Motherboard Support appeared first on TechGoing.

The case measures 202mm width * 266mm depth * 295.2mm height and uses mesh panels on the front, top, and sides.

In terms of expandability, the case supports 200 to 255mm long graphics cards, CPU coolers are limited to 75mm high, and power supplies support 185mm ATX power supplies. The case supports 120mm front fans, 120/140mm models on top, and 120/140mm models on the bottom.

The JOSEPH C6 chassis is made of 0.7mm thick steel and the front ports include USB Type-C x 1, USB 3.0 x 1, and audio ports.

The post Jonsbo C6 case released: supports M-ATX motherboard, four-sided mesh design appeared first on TechGoing.

The D500 is wrapped in a 2.0mm aluminum frame, silver in color, with dust panels on the front, top, and bottom, and a pivoting magnetic side panel for the side panel.

The JONSBO D500 supports 420 cooling positions, 240/280/360/420 cooling at the top and front, and 120/140 cooling at the rear. Battery compartment location can be selected.

In addition, the case supports RTX 40 series graphics cards, up to 480mm, and also supports horizontal and vertical dual modes.

JONSBO D500 supports up to 10+ HDD expansions and also has reserved space for expansion optical drives.

The JONSBO D500 chassis is equipped with dual USB 3.0, Type-C Gen 2 10Gbps+ interfaces on the front side.

The post JONSBO Announce D500 Tower Case: 420 Cooling Support, 10+ Hard Drive Expansion appeared first on TechGoing.

The NAS chassis measures 222.5222.5224mm, with a cubic shape and about 11L volume.

The N2 chassis uses a compartmentalized design, with five 3.5-inch hard drive bays in the front and a 2.5-inch hard drive installed, and also supports PCIe half-height devices.

The N2 chassis features a server-grade hot-swappable backplane and 10um gold-plated SAS hot-swappable interface for long life, according to JOSEPH.

In addition, the case supports a 17*17cm ITX motherboard, CPU cooler height limit of 65mm, the rear panel comes with a 120mm thin fan, support for SFX power supply, and front 10Gbps USB-C interface.

JOSEPH is not officially on the N2 chassis, third-party vendors are selling it for RMB 699.

The post Jonsbo Releases N2 NAS Chassis: 5+1 Trays, 11L Volume appeared first on TechGoing.